agGregATe ImpaCt VaLue REPOrT

  • Aggregate Impact Value Report | PDF | Construction ...

    2018-11-19 · Aggregate Impact Value (AIV) ASTM-D58-74. Introduction: Impact value of an aggregate is the percentage loss of weight particles passing 2.36mm sieve by the application of load by means of 15 blows of standard hammer and drop, under specified test condition. The aggregate impact value gives a relative measure of the resistance of an aggregate to sudden

    Chat Online
  • AIV Lab Report - AGGREGATE IMPACT VALUE

    The Aggregate Impact Value (AIV) (M2/M1)x100 19 % 23 %. AIV = M2/M1 * 100%. Average aggregate impact value of the sample is 21 %. DISCUSSION 1. Give the impact value of a good aggregate to ensure the strength of the. aggregate used in road construction. -Aggregate impact value is measure of toughness of aggregate.

    Chat Online
  • Lab Report.docx - Determination of Aggregate Impact

    Crush samples having an impact value of 12.5% fall in the category of 10-20%, therefore, the aggregate test sample is classified as strong and can be seen in the table below. The aggregate impact value is useful for selecting the good aggregates for road construction. Aggregate appropriate for cement wearing course should have maximum AIV of 30%.

    Chat Online
  • DCC3113 DETERMINATION OF AGGREGATE IMPACT VALUE.

    2017-12-15 · The aggregate impact value indicates a relative measure of the resistance of the aggregate to a sudden shock or impact which in some aggregates differs from its resistance to a slow compressive load. From the calculations done we know that the aggregate can be acceptable as their Aggregate Impact value is less then 20% Aggregate Impact Value 10.

    Chat Online
  • Aggregate Impact Value Test | Impact Test Of Aggregate ...

    2022-1-4 · Aggregate impact value is the ratio of the weight of the fraction passing through 2.36 mm (weight W2) by the total weight of the sample (weight W1 + W2). Aggregate Impact Value = (W2/ (W1+W2)) * 100 = 80 gm / 300 gm = 26.67

    Chat Online
  • Aggregate Impact Value Test - Procedure & Uses - [Civil ...

    2022-1-5 · The average value of the two samples is the Impact Value of Aggregate. Lab Test Report Format. SI: Description: Sample 1 in grams: Sample 2 in grams: 1: Weight of dried sample (W1) 340: 360: 2: Weight of crushed particle passed through 2.36mm sieve (W2) 50: 65: 3: Impact value of Aggregate = (W2/W1) x 100: 15%: 18%:

    Chat Online
  • (DOC) AGGREGATE IMPACT VALUE TEST | hong g.woei -

    The aggregate impact value provides a relative measure of resistance to crushing under a gradually applied compressive load. To achieve a high quality of pavement, lower aggregate impact value should be preferred. Toughness is the property of a material to resist impact. Due to traffic loads, the aggregate are subjected to the pounding action ...

    Chat Online
  • Determination of Aggregate Impact Value - Impact Test on ...

    2010-2-22 · The aggregate impact value is a measure of resistance to sudden impact or shock, which may differ from its resistance to gradually applied compressive load. Procedure o f Aggregate Impact Test The test sample consists of aggregates sized 10.0 mm 12.5 mm. Aggregates may be dried by heating at 100-110° C for a period of 4 hours and cooled.

    Chat Online
  • Aggregate impact value report conclusion

    Aggregate impact value report conclusion Products. As a leading global manufacturer of crushing, grinding and mining equipments, we offer advanced, reasonable solutions for any size-reduction requirements including, Aggregate impact value report conclusion, quarry, aggregate, and different kinds of minerals.

    Chat Online
  • Aggregates for Concrete - CEDD - Home

    2019-6-13 · Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine, copyright ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428. A copy of the complete ASTM

    Chat Online
  • Aggregate Impact Value.docx - REPORT ON AGGREGATE

    This characteristic is measured by impact value test. The aggregate impact value is a measure of resistance to sudden impact or shock, which may differ from its resistance to gradually applied compressive load. The material used for our test is ballast under dry condition. EQUIPMENT 1. Aggregate impact testing machine 2.

    Chat Online
  • (DOC) AGGREGATE IMPACT VALUE TEST | hong g.woei -

    The aggregate impact value provides a relative measure of resistance to crushing under a gradually applied compressive load. To achieve a high quality of pavement, lower aggregate impact value should be preferred. Toughness is the property of a material to resist impact. Due to traffic loads, the aggregate are subjected to the pounding action ...

    Chat Online
  • IMPACT VALUE OF AGGREGATE - iricen.gov

    2019-3-11 · The aggregate impact value gives a relative measure of the resistance of an aggregate to sudden shock or impact, which in some aggregates differs from its resistance to a slow compressive load. 2.Apparatus Required Fig. 1: Balance Balance should be accurate upto 1 g Fig. 2: Sieves Seives required are 12.5, 10.0 and 2.36 mm Fig. 3: Impact ...

    Chat Online
  • Determination of Aggregate Impact Value - Impact Test on ...

    The aggregate impact value is a measure of resistance to sudden impact or shock, which may differ from its resistance to gradually applied compressive load. Procedure o f Aggregate Impact Test The test sample consists of aggregates sized 10.0 mm 12.5 mm. Aggregates may be dried by heating at 100-110° C for a period of 4 hours and cooled.

    Chat Online
  • Methods for determination of aggregate impact value

    2019-10-18 · Aggregate Impact Value (AIV) = 𝑾 𝑾 × Calculate the mean of the two results to the nearest whole number. Report the mean as the aggregate impact value, unless the individual results differ by more than 0.15 times the mean value. In

    Chat Online
  • Determination of Aggregate Impact Value Impact Test on

    2021-5-21 · Lab Report of Los Angeles Abrasion Test on a Given Sample. The Los Angeles test is a measure of degradation of mineral aggregates of standard gradings resulting from a combination of actions including abrasion or attrition, impact, and grinding in a rotating steel drum containing a specified number of steel spheres.

    Chat Online
  • Impact Test of Aggregate | Lab Test Procedure ...

    2022-1-4 · The procedure of the impact value test includes the following series of steps: 1. The aggregate samples of size 10mm to 12.5mm (passing through 12.5mm sieve and retained on 10mm sieve) are first taken and oven-dried at a temperature ranging from 100 degrees Celsius to 110 degrees Celsius for about four hours. 2.

    Chat Online
  • AGGREGATE IMPACT TEST by Nurul Afiqah - Prezi

    2014-3-26 · design by Dóri Sirály for Prezi AGGREGATE IMPACT TEST In conclusion,the percentage of aggregate’s wear depends on the quality of aggregate. In this test, we can conclude that: The loss of aggregate = 1663 g

    Chat Online
  • Aggregate - Wiley Online Library

    Aggregate aims to publish on a wide variety of topics that focus on the processes of aggregation of atoms, ions, molecules, oligomers, polymers, clusters, particles, gels, hybrids, composites, cells, pathogens, etc. in a broad range of areas such

    Chat Online
  • Aggregates for Concrete - CEDD - Home

    2019-6-13 · Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine, copyright ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428. A copy of the complete ASTM

    Chat Online
  • Methods for determination of aggregate impact value

    2019-10-18 · Aggregate Impact Value (AIV) = 𝑾 𝑾 × Calculate the mean of the two results to the nearest whole number. Report the mean as the aggregate impact value, unless the individual results differ by more than 0.15 times the mean value. In

    Chat Online
  • Aggregate Impact Test to Find Aggregate Impact Value ...

    The aim and purpose of aggregate impact test is to determine the impact value of the given aggregate which is to be used in road works. Toughness is the property of a material to resist impact. Due to traffic loads the road stones are subjected to the pounding action or impact and there is possibility

    Chat Online
  • Determination of aggregate impact value (AIV) of given ...

    2020-2-13 · Determination of aggregate impact value (AIV) of given aggregate sample (BS-812) Significance: Aggregates used in the construction of roads should be strong enough to resist crushing under traffic wheel loads. It gives relative measure of the resistance of an aggregate to sudden shock or impact.

    Chat Online
  • Aggregate Impact Value Test | Construction Aggregate ...

    2017-10-4 · The cup is fixed firmly in position on the base of the M1 - (M2+M3) 1.0 g 1.9 -1.7 -0.8 the aggregate impact value and more the aggregate impact value less is the hammer machine and the whole of the test sample from 2 32.7 31.5 33.4 To determine the aggregates toughness of the road aggregates and the cylindrical measure is transferred to the cup.

    Chat Online
  • Determination of Aggregate Impact Value Impact Test on

    2021-5-21 · Lab Report of Los Angeles Abrasion Test on a Given Sample. The Los Angeles test is a measure of degradation of mineral aggregates of standard gradings resulting from a combination of actions including abrasion or attrition, impact, and grinding in a rotating steel drum containing a specified number of steel spheres.

    Chat Online
  • Impact Test of Aggregate | Lab Test Procedure ...

    2022-1-4 · The procedure of the impact value test includes the following series of steps: 1. The aggregate samples of size 10mm to 12.5mm (passing through 12.5mm sieve and retained on 10mm sieve) are first taken and oven-dried at a temperature ranging from 100 degrees Celsius to 110 degrees Celsius for about four hours. 2.

    Chat Online
  • AGGREGATE IMPACT TEST by Nurul Afiqah - Prezi

    2014-3-26 · design by Dóri Sirály for Prezi AGGREGATE IMPACT TEST In conclusion,the percentage of aggregate’s wear depends on the quality of aggregate. In this test, we can conclude that: The loss of aggregate = 1663 g

    Chat Online
  • Aggregate - Wiley Online Library

    Aggregate aims to publish on a wide variety of topics that focus on the processes of aggregation of atoms, ions, molecules, oligomers, polymers, clusters, particles, gels, hybrids, composites, cells, pathogens, etc. in a broad range of areas such

    Chat Online
  • (DOC) Aggregate crushing value Test Lab Report | Adnan ...

    6) Release the load and remove the material from the cylinder. 7) Sieve the material with 2.36mm IS sieve, care being taken to avoid loss of fines. 8) Weigh the fraction passing through the IS sieve. Calculation: After 2.36 (8) sieves retained = 1990 gram. 2500−1990 ACV = × 100 2500 f = 20.4 % Result: Aggregate crushing value = 20.4% Result ...

    Chat Online
  • Aggregates for Concrete - CEDD - Home

    2019-6-13 · Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine, copyright ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428. A copy of the complete ASTM

    Chat Online
ZhengZhou N-CAI Corporation © 2020 Copyright.Crusher